AT-EW80P / AT-EW120P / AT-EW160P

Electric PCB Wet-film Screen Printer

ATMA AT-EW120P Electric PCB Wet-film Screen Printer
AT-EW120P Electric PCB Wet-film Screen Printer
ATMA Logo
Suitable for Rigid Printed Circuit Board, Flexible PCB, PCB legend, Photo Resistance Solder Mask, Wet-Film Plug-via-holes, Surface Mounted Technology, Carbon/Resin Plug-via-holes, and other PCB screen printing.

VIDEOS:

Patented Design:
Innovative double squeegee two-way printing, plus bidirectional peel-off and table displacement.
Double Printer Processing:
Finished both sides printing to dry at once to reduce processing and save energy consumption.
Fast Elevation:
Electric vertically up down, fast moving to raise productivity 30% or above, long run durable operation.
Open Mesh Printing:
Save the cost for screen making, fast screen registration to reduce technical difficulty.
Safety Guard:
Equipped with safety bar, safety press bar and emergency stop uplifting cylinder for thorough protection.
A. German S.E.W. Motor powers screen up / down position and servo driven print head travel. Provides high cycle speed with smooth mechanical movements, low noise and accuracy.

B. Print table displacement can be set incrementally in X/Y axis to follow printing stroke correcting bi-directional printing offset. Table displacement stroke can be adjusted as needed based on ink transfer demand or buildup of residual ink on mesh while printing.

C. Travel of print head on guided precision sealed linear motion bearings, reinforced tooth belt, timing belt wheel for high rigidity and ultra-smooth high print speed transport cycles without backlash. This ultra-smooth gliding of the squeegee / flood assembly enables step-less speed change for higher production speed, smooth operation, consistent / uniform printing deposit control, less maintenance and fast operation.

D. Print head high-park capability facilitates faster setup and changeover.

E. Pneumatic frame locking with check valves / airlock and four-sided frame holding assembly ensures rigidity and high stability.

F. Patented mechanical print head lift guided on precision sealed linear motion bearings allows stable, vibration-free movement in up/down positions.

G. Print head printing parameter settings for speed, height up/down position and manual travel for set up independently controlled by single action from the touch screen.

H. Innovative double squeegee two-way printing (bi-directional) beneficial for two machine processing or single machine to complete double-sided printing, once dried to raise production efficiency. Includes pneumatic squeegee pressure equalizer control system. Automatic and regulated with pivot point balance with snow plow skew for irregular print surfaces.

I. Stable pneumatic cylinders are encased around solid cast to allow consistent pressurization. After initial setup pressure regulator can be increased and decreased on the fly. For most applications suitable pressure range is 3-4 bars, and pressure indicators gauge incremental setting adjustment.

J. Touch screen control of innovative double peel-off action to assist with release of ink and mesh from substrate synchronized with the double squeegee two-way printing stroke

K. Peel-off height lifting point adjustable by low speed cylinder depending on print stroke and mechanical adjustment to set peel-off height.

L. Mechanical adjustment of off-contact height settings to accommodate substrate thickness 0 - 25 mm (0 - 1”).

M. Print table X / Y movements via precision scaled micrometer control(s) for fine registration. Play-free registration without backlash.

N. Choice of three functions: Double squeegee print mode A: screen lowers, table moves X direction and then Y direction, squeegee prints, table goes back to original X and Y position, prints again, and then screen goes up to standby position. Double squeegee print mode B: First cycle screen goes down, table moves in X-direction, prints, table goes back to original position in X direction. Second cycle: Screen goes down again, table moves in both X and Y direction, prints, table goes back to original position in X direction, prints again, screen goes up and table goes back to original position in the Y direction. Standard printing mode: screen will go down, squeegee prints right-to-left, screen goes up, and flood coater moves to the right to left and brings the ink back as the screen goes up. This printing mode is for squeegee and flood coater (instead of double squeegee) as there will be no printing done from left to right.

O. Print head assembly is synchronized and changeover is pneumatically operated for smoother transition. Adjustable height controls, angle settings 0-30°, leveling and skew feature. Provides uniform ink deposits across the entire print area.

P. Highly efficient delta servo motor powers Print head with greater accuracy acceleration and deceleration of speed range. Direct numeric input of digital settings for stroke position through touch screen control.

Q. Variable and independent Print head stroke speed and length setting to image size.

R. Productivity preset in numerical values for throughput can be changed anytime. Enter production quantity according to run length and during run the touch screen will indicate current yield until preset number of prints are achieved.

S. Frame loading and unloading from the front of the machine to facilitate fast setup and changeovers. Frame holding rails can be unlocked from touch screen and easily adjusted to the size of the frame.

T. Control system for compressed air supply is an oil free FRL unit to prevent oil mist pollution, applicable in clean room environment.

U. Emergency press plate positioned in front of print table in case substrate alignment is not in the correct position. Operator can press the plate and printing head slowly lifts up to the full upright home position allowing operator the chance to register correctly final substrate alignment. Reduces spoilage and yields more printed product.

V. Front safety bar location on the print head, compliant with OSHA safety regulations.

W. Includes 4 squeegee holders and 4 flood coaters, sq. / fl clamps, pedal switch control, toolbox, tools and door key.

X. Includes squeegee holders, squeegee holder clamps, foot pedal switch control, toolbox, tools, and door key.
Model AT-EW80P
Metric
AT-EW80P
US Standard Units
AT-EW120P
Metric
AT-EW120P
US Standard Units
AT-EW160P
Metric
AT-EW160P
US Standard Units
Substrate Thickness 0.1〜25 mm 0 - 1" 0.1〜25 mm 0 - 1" 0.1〜25 mm 0 - 1"
Max productivity 200〜400 P/H 180〜370 P/H 150〜260 P/H
Max printing area 600x650mm 23.6" x 25.6" 600x950mm 23.6" x 37.4" 600x1300mm 23.6" x 51"
Table Size 700x900mm 27.6" x 35.4" 700x1200mm 27.6" x 47" 800x1700mm 31.5" x 67"
Max Frame O/D Size 900x1100mm 35.4" x 43.3" 1000x1500mm 39.4" x 59" 1000x1900mm 39.4" x 75"
Printing-head Swivel Angle ±9° ±9° ±9°
Power Source 3Φ, 220V/380V, 50/60Hz 3Φ, 220V/380V, 50/60Hz 3Φ, 220V/380V, 50/60Hz
Power Consumption 2.6kw 2.6kw 2.6kw
Air Exhaustion 16 L/min 0.56 cfm 17.31 L/min 0.61 cfm 21.25 L/min 0.75 cfm
Machine Weight 670kg 1477 lbs 800kg 1764 lbs 920 kg 2,028 lbs
Machine Dimension 1700x1300x1700mm 67" x 51" x 67" 1900x1400x1750mm 75" x 55" x 69" 2300 x 1400 x 1710mm 90" x 55" x 67"
• Table vacuum
• Safety Light-Beam
• Thicker squeegee rubber to enhance effect of Plug-via
• Scratch Residual Ink for automatic cleaning of residue paste/chemical buildup underneath mesh.

• Others available upon request.